Megatouch Titanium 2 CD to Hard Drive Upgrade (PM0350-02)

Instructions (PM0350-02) for upgrading a Megatouch Titanium 2 game from CD to hard drive.

merit industries, inc.

PM0350-02

Visit the Merit Industries, Inc. Web Site

http://www.meritind.com

CD TO HARD DRIVE

UPGRADE

Table of Contents

Countertop Section

CMOS Update and CD-ROM Removal ............................................................... p. 2

Hard Drive Installation......................................................................................... p. 3

Centronics Connector Board Assembly/Installation ............................................ p. 3-4

Installing a Button Key/Adapter Board ................................................................ p. 4

Cabaret/Upright (front-access) Section

CMOS Update and CD-ROM Removal ............................................................... p. 5

Hard Drive Installation......................................................................................... p. 5

Centronics Connector Board Assembly/Installation ............................................ p. 5-6

Installing a Button Key/Adapter Board ................................................................ p. 6

Upright (rear-access) Section

CMOS Update and CD-ROM Removal ............................................................... p. 7

Hard Drive Installation......................................................................................... p. 7-8

Centronics Connector Board Assembly/Installation ............................................ p. 8

Installing a Button Key/Adapter Board ................................................................ p. 8

Installing the Side Decals on a Countertop Game.................................... p. 18

Troubleshooting After Installation ................................................................ p. 19

Championship Edition Instructions

(For Championship Kits Only)

Overview ............................................................................................................. p. 20

Programming a Tournament ............................................................................... p. 21-23

Awarding Prizes .................................................................................................. p. 24

Pay Without PIN.................................................................................................. p. 24

Software License Agreements ....................................................................... p. 25-30

English ................................................................................................................ p. 25-26

French ................................................................................................................. p. 27-28

German ............................................................................................................... p. 29-30

Megatouch™ Titanium 2 Edition

Megatouch™ XL Titanium 2 Hardware Requirements

In order to successfully upgrade your unit, your Megatouch™ XL game must be currently

running the Megatouch™ XL 6000, Gold, or Platinum software. In order to check the

program running on your game, push the set-up button inside the cabinet. The program

information will be displayed in the upper left corner of the first screen that appears. If you

are running XL 6000 software, the program number will be PG3001-00-XX or PG3001-01-

XX. If you are running Gold software, the program number will be PG3001-02-XX, PG3001-

03-XX, or PG3001-04-XX. If you are running Platinum software, the program number will

be PG3004-01-XX.

If your game is not currently at this level you will need to upgrade the RAM and video RAM.

Merit Industries offers the necessary hardware for this upgrade through the Megatouch

Hardware Upgrade Kit (KUV-107-027-02). Contact your distributor to purchase this hard-

ware upgrade kit.

CONTENTS:

QTY

PART NUMBER

DESCRIPTION

EC2198-01

CENTRONICS RIBBON CABLE

HW4101

MACHINE SCREW, PAN/PHL, #4-40x3/8

HW4325

SHEET METAL SCREW, PAN/PHL, #6x1/2

HW3050

KEPNUT, #4-40

MW0444-01

CENTRONICS MOUNTING BRACKET

SA0200-21

TITANIUM 2 HDD W/SLED ASSEMBLY

MW0302-01

ADAPTER CARRIAGE, UR, HDD ASSY

HW3201

KEPNUT, #8-32

HW4249

SEMS SCREW, PAN/PHL, #6-32x3/8

PA0018-01

UPGRADE PROGRAM CD

SA10053-01

BUTTON KEY ADAPTER BOARD

HW3100

FINISHING NUT, #6-32

HW6036-03

STAND OFF #6-32 x 1/4

HW4206

MACHINE SCREW #6-32 x 1/4

HW8121-01

CONTACT CLEANER

SA3052-XX or
SA3053-XX

TITANIUM BUTTON KEY or
TITANIUM CHAMPIONSHIP KEY

GL3100-30

COUNTERTOP TITANIUM DECAL, L

GL3100-31

COUNTERTOP TITANIUM DECAL, R

CAUTION:

Before performing any upgrade, it is important to remove any static electricity

from your body. To remove static electricity from your body, ground yourself by touching a

grounded piece of metal on the game before handling any boards, chips, connectors, etc.

Failure to ground yourself before performing an upgrade may result in damage to your

system and may prevent you from performing the upgrade.

1 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-02

CMOS Update and CD-ROM
Removal

Unlock and open the CD-ROM door to

access the CD-ROM drive.

Turn on the game and remove the ex-

isting game CD. Insert new the CD la-

beled PA0018-01 into the CD-ROM

drive. (If the CD is not placed into the

drive before the boot-up sequence be-

gins, turn off the game and power back

up.)

The game will continue its normal boot-

up sequence. At the same time, the CD

will load the necessary drivers into the

game to auto-detect the hard drive,

once it is installed.

After the update is complete, you will

get a screen that says: “System CMOS

configured.” See Figure 1.

Remove the CD, turn off the power to

the game and disconnect it from its

power source.

Remove the lid (for lid removal instruc-

tions see the decal located inside the

rear door). Put the lid down before

lifting it off the game.

Remove the touchscreen controller and

disconnect the touchscreen controller

cable from the back of the controller.

Also, disconnect the Molex connector

connecting the orange and gray wires

(from the touchscreen controller cable)

to the harness. Disconnect the green

wire with the ring lug that is attached

to the metalwork, next to the controller.

See Figure 2 for touchscreen control-

ler location.

Disconnect the monitor signal connec-

tor on the motherboard. See Figure 2.

Remove the four nuts securing the

monitor chassis to the main chassis;

t w o nuts are located on each side of

the monitor board. See Figure 3 for

locations.

NOTE: BE CAREFUL TO AVOID THE
FLYBACK TRANSFORMER AND HIGH
VOLTAGE WIRE RUNNING TO THE
MONITOR.

10. Disconnect the monitor power connec-

tion (black and white wires running from

the monitor board to the right angle con-

nector plugged into the power supply).

Remove the green wire from the ground

lug if applicable.

11.

Pick up the monitor assembly and re-

move it from the cabinet.

12. Remove the ribbon cable from the cable

clamp and disconnect it from the IDE-1

location on the motherboard. See Fig-

ure 2.

NOTE: When disconnecting the ribbon
cable, carefully disconnect the cable
by grasping the connector and not the
cable itself.

13. Disconnect the (4)-pin power connec-

tor from the mating connector on the

power supply.

14. Remove the two screws securing the

CD-ROM and remove it from its loca-

tion.

15. Disconnect the speaker connector

(black and white wires) from the J9

location on the I/O board. See Figure 8.

16. Remove the hexnuts securing the cable

clamps on the chassis, also remove

the hexnut securing the ring lug on the

ground braid attached to the chassis

(refer to Figure 4).

COUNTERTOP GAMES

PM0350-02 MEGATOUCH™ TITANIUM 2 EDITION KIT 2

Hard Drive Installation

NOTE: Before you begin the installation of

the hard drive, you must adjust the jumper

settings on the I/O board. (JP-1 EPROM

ENABLED, MUST BE SET TO THE OPEN

POSITION). See Figure 8.

17. Remove the hexnuts securing the cable

clamps and ground wire located on the

lower edge of the chassis to make room

for the hard drive installation. Slide the

hard drive assembly under the

motherboard mounting frame and place

it over the studs on the chassis, mak-

ing sure the hard drive rests against

the CD-ROM drive support. Also make

sure the pin on the edge of the hard

drive is through the slot on the support.

Then replace the ground wire and the

cable clamps. Secure the hard drive

assembly to the chassis using the

hexnuts removed in step 16. See Fig-

ure 4 for orientation.

18. Replace the ring lug on the ground braid

over the stud on the chassis and se-

cure it with existing hexnut (See Fig-

ure 4).

19. Connect the 2 x 20- pin IDE ribbon cable

on the hard drive to the IDE-1 location

on the motherboard. (Make sure that

the red stripe on the ribbon cable

matches up with pin-1 on the IDE-1 lo-

cation on the motherboard. See Figure

6 for location.

20. Connect the power connector on the

hard drive to the mating connector on

the power supply harness.

21. Reinstall the monitor assembly, sliding

it forward as far as possible, and se-

cure it with the existing hardware.

22. Connect the monitor A/C power con-

nector (black and white wires) and

reconnect the ground wire to the ring

lug, if applicable.

23. Reconnect the monitor signal cable to

the J17 location on the motherboard.

24. Route the touchscreen controller con-

nector under the picture tube and away

from the flyback transformer. Then re-

connect the touchscreen controller

cable in the back of the controller and

secure the controller with the existing

hardware.

25. Reconnect the molex connector, con-

necting the orange and gray wires to

the harness. Also place the ring lug on

the touchscreen controller ground to

metalwork and secure with existing

hardware.

26. Reconnect the speaker connector to

the I/O board. See Figure 8 for loca-

tion.

Centronics Ribbon Cable
Assembly/Installation

27. Attach the 2 x 20-pin IDE centronics

ribbon cable (EC2198-01) to the

centronics mounting bracket (MW0444-

01). Secure the ribbon cable to the

mounting bracket, using (2) HW4101

screws and (2) HW3050 nuts. See

Figure 5.

28. Remove the power supply harness

from the cable clamps along the top

edge of the motherboard display frame.

29. Remove the hexnuts securing the cable

clamps to the motherboard display

frame.

3 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-02

30. Mount the centronics connector

bracket on the studs. Reinstall the

cable clamps and secure it in place

using the existing hardware. See Fig-

ure 6.

31. Connect the 2 x 20-pin IDE centronics

ribbon cable (EC2198-01) to IDE-2 on

the motherboard assembly. (Make sure

the red stripe on the ribbon cable

matches up with pin 1 on the IDE-2

interface connector on the

motherboard.) See Figure 6 for loca-

tion.

32. Connect the (4)-pin power connector

on centronics ribbon cable to the mat-

ing connector on the power supply

harness.

Button Key/Adapter Board
Installation

33. If you already have the button key

adapter board installed in your game

(refer to Figure 18), remove the exist-

ing security key from the adapter board

and replace it with the security key

supplied in this kit. Skip to step 41.

34. Using Figure 8, locate the existing se-

curity key, on the I/O board of the

motherboard assembly, and remove it

from the board. (To remove the exist-

ing key, you may need to cut away

silicone sealant holding the key in

place.)

Be extremely careful not to

damage the board.

35. Remove the 1/4” kepnut on the I/O board

as shown in Figure 16. Re-secure the

I/O board using the provided female/

male threaded standoff. (Make sure

not to overtighten standoff as it may

cause damage to the board.) See Fig-

ure 17 for standoff location.

36. Apply a small amount of the contact

cleaner to the adapter board contacts.

See Figure 17 for contact locations.

37. Install the adapter board by aligning the

contacts on the adapter board to the

security key contacts. Make sure that

all five contacts are mounted properly.

See Figure 17.

38. Secure the adapter board in place,

using the 1/4” kepnut removed in step

35. (Make sure not to overtighten nut

as it may cause damage to the board.)

39. Insert the round security key into the

key socket on the adapter board. See

Figure 18.

40. Make sure all DIP switches on DS2 and

DS3 are set to the

OFF position. See

Figure 8.

41. Install the hood, connecting the fan

power connector, ground straps and

plastic drain tube. Pull hood towards

you until the spring-loaded levers lock

into place.

42. Plug in the game and turn on the power.

PM0350-02 MEGATOUCH™ TITANIUM 2 EDITION KIT 4

Cabaret CMOS Update and
CD-ROM Removal

Plug in the game.

Open the CPU section door.

Slide the CPU shelf into its service po-

sition.

Turn on the game and remove the ex-

isting game CD. Insert new the CD la-

beled PA0018-01 into the CD-ROM

drive. (If the CD is not placed into the

drive before the boot-up sequence be-

gins, turn off the game and power back

up.)

The game will continue its normal boot-

up sequence. At the same time, the CD

will load the necessary drivers into the

game to auto-detect the hard drive,

once it is installed.

After the update is complete, you will

get a screen that says: “System CMOS

configured.” See Figure 1.

Remove the CD and turn off the power

to the game and disconnect it from its

power source.

Disconnect the ribbon cable from the

IDE-1 location on the motherboard. See

Figure 9.

Locate the L-bracket on the right side

of the CD-ROM and remove the screw

securing the CD-ROM to the bracket.

See Figure 9.

10. Remove the two screws on the left

side of the CD-ROM. See Figure 9.

11.

Disconnect the (4)-pin power connec-

tor on the CD-ROM and remove the CD-

ROM from the game.

Hard Drive Installation

NOTE: Before you begin the installation of

the hard drive, you must adjust the jumper

settings on the I/O board. (JP-1 EPROM

ENABLED, MUST BE SET TO THE OPEN

POSITION). See Figure 8.

12. Mount the hard drive on the adapter

carriage plate (MW0302-01). Secure

the hard drive to the carriage plate,

using the supplied #8-32 kepnut

(HW3201). See Figure 7.

13. Secure the hard drive assembly to the

right and left CD-ROM brackets using

the (3) HW4249 screws. See Figure

12.

14. Connect the 2 x 20- pin IDE ribbon cable

on the hard drive to the IDE-1 location

on the motherboard. (Make sure that

the red stripe on the ribbon cable

matches up with pin-1 on the IDE-1 lo-

cation on the motherboard.) See Fig-

ure 10 for location.

15. Connect the (4)-pin power connector

on the hard drive to the mating connec-

tor on the power supply harness. See

Figure 10.

Centronics Ribbon Cable Assem-
bly/Installation

16. Attach the 2 x 20-pin IDE centronics

ribbon cable (EC2198) to the centronics

mounting bracket (MW0444-01). Se-

cure the ribbon cable to the mounting

bracket, using the (2) HW4101 screws

and (2) HW3050 nuts. See Figure 5.

17. Mount the centronics cable assembly

along the front edge of the hard drive

adapter plate. Secure the centronics

bracket to the CPU shelf using the (2)

HW4325 screws. See Figure 10.

FRONT-ACCESS UPRIGHT AND CABARET GAMES

5 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-02

18. Connect the 2x20-pin IDE centronics

ribbon cable (EC2198-01) to IDE-2 on

the motherboard assembly. (Make sure

the red stripe on the ribbon cable

matches up with pin 1 on the IDE-2 in-

terface connector on the motherboard.)

See Figure 10.

19. Connect the (4)-pin power connector

on the centronics ribbon cable to the

mating connector on the power supply

harness.

Button Key/Adapter Board
Installation

20. If you already have the button key

adapter board installed in your game

(refer to Figure 18), remove the exist-

ing security key from the adapter board

and replace it with the security key

supplied in this kit. Skip to step 27.

21. Using Figure 8, locate the existing se-

curity key, on the I/O board of the

motherboard assembly, and remove it

from the board. (To remove the exist-

ing key, you may need to cut away sili-

cone sealant holding the key in place.)

Be extremely careful not to dam-

age the board.

22. Remove the 1/4” kepnut on the I/O board

as shown in Figure 16. Re-secure the

I/O board using the provided female/

male threaded standoff. (Make sure

not to overtighten standoff as it may

cause damage to the board.) See Fig-

ure 17 for standoff location.

23. Apply a small amount of the contact

cleaner to the adapter board contacts.

See Figure 17 for contact locations.

24. Install the adapter board by aligning the

contacts on the adapter board to the

security key contacts. Make sure that

all five contacts are mounted properly.

See Figure 17 for orientation.

25. Secure the adapter board in place,

using the 1/4” kepnut removed in step

22. (Make sure not to overtighten stand-

off as it may cause damage to the

board.)

26. Insert the round security key into the

key socket on the adapter board. See

Figure 18.

27. Make sure all DIP switches on DS2 and

DS3 are set to the

OFF position. See

Figure 8.

28. Slide the CPU shelf back into position,

plug in the game and turn on the power.

PM0350-02 MEGATOUCH™ TITANIUM 2 EDITION KIT 6

CMOS and CD-ROM Removal

Open the rear door.

Slide the CPU shelf into its service po-

sition.

Turn on the game and remove the ex-

isting game CD. Insert new the CD la-

beled PA0018-01 into the CD-ROM

drive. (If the CD is not placed into the

drive before the boot-up sequence be-

gins, turn off the game and power back

up.)

The game will continue its normal boot-

up sequence. At the same time, the CD

will load the necessary drivers into the

game to auto-detect the hard drive,

once it is installed.

After the update is complete, you will

get a screen that says: “System CMOS

configured.” See Figure 1.

Remove the CD, turn off the power to

the game and disconnect from its

power source.

Open the coin mech door and locate

the two screws securing the CD player

to the metalwork (see Figure 13 for

screw location). Remove both screws.

Access the rear of the game.

Remove the screw securing the front

edge of the metalwork to the wood

shelf.

10. Gently push the power supply to the

right to access the metalwork behind

it. (You may need to disconnect the

line cord from the power supply and/or

cable clamp to the right of the power

supply, in order to slide the power sup-

ply to the right.)

11.

Locate the remaining screw, located

behind the power supply and beneath

the motherboard assembly, securing

the CD player to the metalwork, and

remove it (see Figure 14 for location).

12. Slide the CD player to the left so you

can access the rear of the player.

13. Disconnect the (4)-pin power connec-

tor. Also disconnect the ribbon cable

on the CD-ROM, and from the IDE-1 lo-

cation on the motherboard. See Figure

15.

14. Remove the CD-ROM from the game.

Hard Drive Installation

NOTE: Before you begin the installation of

the hard drive, you must adjust the jumper

settings on the I/O board. (JP-1 EPROM

ENABLED, MUST BE SET TO THE OPEN

POSITION). See Figure 8.

15. Mount the hard drive on the adapter

carriage plate (MW0302-01). Secure

the hard drive to the carriage plate,

using the supplied #8-32 kepnut

(HW3201). See Figure 7.

16. Install the hard drive. Slide hard drive

forward underneath the motherboard

assembly, matching up the holes on the

adapter plate (MW0302-01), with the

existing holes on the metalwork. See

Figure 15.

17. Secure the adapter plate to the metal-

work using the (3) HW4249 screws.

See Figure 15.

REAR-ACCESS UPRIGHT GAMES

7 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-02

18. Connect the 2 x 20- pin IDE ribbon cable

on the hard drive to the IDE-1 location

on the motherboard. (Make sure that

the red stripe on the ribbon cable

matches up with pin-1 on the IDE-1 lo-

cation on the motherboard.) See Fig-

ure 15 for location.

19. Connect the (4)-pin power connector

on the hard drive to the mating connec-

tor on the power supply harness.

Centronics Ribbon Cable
Assembly/Installation

20. Attach the 2 x 20-pin IDE centronics

ribbon cable (EC2198) to the centronics

mounting bracket (MW0444-01). Se-

cure the ribbon cable to the mounting

bracket, using the (2) HW4101 screws

and (2) HW3050 nuts. See Figure 5.

21. Mount the centronics cable assembly

along the front edge of the hard drive

adapter plate. Secure the centronics

bracket to the CPU shelf using the (2)

HW4325 screws. See Figure 15.

22. Connect the 2x20-pin IDE centronics

ribbon cable (EC2198-01) to IDE-2 on

the motherboard assembly. (Make sure

the red stripe on the ribbon cable

matches up with pin 1 on the IDE-2 in-

terface connector on the motherboard.)

See Figure 15.

23. Connect the (4)-pin power connector

on the centronics ribbon cable to the

mating connector on the power supply

harness.

Button Key/Adapter Board
Installation

24. If you already have the button key

adapter board installed in your game

(refer to Figure 18), remove the exist-

ing security key from the adapter board

and replace it with the security key

supplied in this kit. Skip to step 31.

25. Using Figure 8, locate the existing se-

curity key, on the I/O board of the

motherboard assembly, and remove it

from the board. (To remove the exist-

ing key, you may need to cut away sili-

cone sealant holding the key in place.)

Be extremely careful not to dam-

age the board.

26. Remove the 1/4” kepnut on the I/O board

as shown in Figure 16. Re-secure the

I/O board using the provided female/

male threaded standoff. (Make sure

not to overtighten nut as it may cause

damage to the board.) See Figure 17

for standoff location.

27. Apply a small amount of the contact

cleaner to the adapter board contacts.

See Figure 17 for contact locations.

28. Install the adapter board by aligning the

contacts on the adapter board to the

security key contacts. Make sure that

all five contacts are mounted properly.

See Figure 17 for orientation.

29. Secure the adapter board in place,

using the 1/4” kepnut removed in step

26. (Make sure not to overtighten nut

as it may cause damage to the board.)

30. Insert the round security key into the

key socket on the adapter board. See

Figure 18.

31. Make sure all DIP switches on DS2 and

DS3 are set to the

OFF position. See

Figure 8.

32. Slide the CPU shelf back into position,

plug in the game and turn on the power.

PM0350-02 MEGATOUCH™ TITANIUM 2 EDITION KIT 8

FIGURE 1 - CMOS UPDATE COMPLETE SCREEN

FIGURE 2 - INTERNAL VIEW WITH MONITOR ASSEMBLY REMOVED

9 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-02

FIGURE 3 - LOCATION OF NUTS FOR REMOVING MONITOR ASSEMBLY

FIGURE 4 - HARD DRIVE INSTALLATION

MONITOR
BOARD

FLYBACK

TRANSFORMER

HIGH VOLTAGE

WIRE

NUTS

IDE RIBBON CABLE

HARD DRIVE

RING LUG

GROUND WIRE

RAILS

CD-ROM SUPPORT

HARD DRIVE

PM0350-02 MEGATOUCH™ TITANIUM 2 EDITION KIT 10

FIGURE 5 - CENTRONICS ASSEMBLY COMPONENTS

FIGURE 6 - CENTRONICS/HARD DRIVE IDE-RIBBON CABLES INSTALLED

SIGNAL

MONITOR

CABLE

PIN-1 ON THE CENTRONICS
IDE RIBBON CABLE

(IDE - 2 LOCATION)

CENTRONICS

MOUNTING
BRACKET

PIN - 1 ON THE
HARD DRIVE
RIBBON CABLE

(IDE-1 LOCATION)

EC2198-01
(PIN-1)

MW0444-01

CONNECT TO

POWER SUPPLY

CONNECTOR

CONNECT TO

IDE-2 ON

MOTHERBOARD

HW4101

(2 PLACES)

11 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-02

SECURITY KEY

LOCATION ON THE
I/O BOARD

JP-1
(EPROM ENABLED)

SPEAKER CONNECTOR

DS2

DS3

FIGURE 8 - I/O BOARD LOCATIONS

FIGURE 7 -HARD DRIVE/ADAPTER PLATE INSTALLATION

ADAPTER CARRIAGE PLATE

CONNECT TO

POWER SUPPLY

CONNECT TO

IDE 1 ON THE
MOTHERBOARD

HW3201

PIN-1

PM0350-02 MEGATOUCH™ TITANIUM 2 EDITION KIT 12

Cabaret

(Front Access)

FIGURE 9 - CD-ROM ACCESS/REMOVAL

FIGURE 10 - HARD DRIVE/CENTRONICS INSTALLATION

"LEFT" SIDE

BRACKET

"RIGHT" SIDE

L-BRACKET

IDE-1
LOCATION ON

THE MOTHERBOARD

CD-ROM

MOTHERBOARD

& I/O BOARD

ASSEMBLY

HW4249
(3 PLACES)

HW4325

(2 PLACES)

POWER CONNECTOR

CONNECT TO MATING

CONNECTOR ON POWER

SUPPLY HARNESS

IDE 2 LOCATION

ON THE MOTHERBOARD

IDE 1 LOCATION

ON THE MOTHERBOARD

13 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-02

Upright

(Front Access)

FIGURE 11 - CD-ROM ACCESS/REMOVAL

FIGURE 12 - HARD DRIVE/CENTRONICS INSTALLATION

IDE-2 LOCATION

ON THE I/O BOARD

IDE-1 LOCATION

ON THE I/O BOARD

HW4325

(2 PLACES)

POWER CONNECTOR

CONNECT TO MATING

CONNECTOR ON POWER

SUPPLY HARNESS

HW4249

(3 PLACES)

"LEFT" SIDE

BRACKET

IDE-1
LOCATION ON

THE MOTHERBOARD

"RIGHT" SIDE

L-BRACKET

PM0350-02 MEGATOUCH™ TITANIUM 2 EDITION KIT 14

Upright

(Rear Access)

FIGURE 13 - CD-ROM HARDWARE LOCATION

FIGURE 14 - HARD DRIVE/CENTRONICS INSTALLATION

TOWARD

REAR DOOR

CD-ROM PLAYER

MOUNTING SCREW
LOCATIONS

15 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-02

FIGURE 15- HARD DRIVE/CENTRONICS INSTALLATION

HW4325

(2 PLACES)

CENTRONICS BRACKET
AND RIBBON CABLE ASSEMBLY

IDE 1 LOCATION

ON THE MOTHERBOARD

CONNECT TO

IDE 1 ON THE MOTHERBOARD

CONNECT TO MATING

CONNECTOR ON THE

POWER SUPPLY HARNESS

HW4249

(3 PLACES)

IDE 2 LOCATION

ON THE MOTHERBOARD

CONNECT TO

MATING CONNECTOR

ON THE POWER SUPPLY

HARNESS

CONNECT TO

IDE 2 ON THE MOTHERBOARD

PM0350-02 MEGATOUCH™ TITANIUM 2 EDITION KIT 16

1/4” Kepnut

FIGURE 16 - 1/4” KEPNUT LOCATION ON THE I/O BOARD

Security Key
contacts

M a l e / F e m a l e
Standoff

Adapter Board

Contacts

Security Key Contacts

Adapter Board

FIGURE 17 - ADAPTER BOARD MOUNTING LOCATION ON I/O BOARD

17 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-02

FIGURE 18 - ADAPTER BOARD AND KEY INSTALLED

Remove the existing side decals. (Remove any remaining adhesive residue with an

adhesive remover.)

NOTE: Make sure not to get any adhesive removing solvents or solutions on the
touchscreen, as they may damage the touchscreen.

When you are finished removing any excess adhesive from the game, wipe the sur-

faces with alcohol solvent. The surfaces must be clean and free from dirt for the new

decals to adhere properly.

Partially peel the backing from the top edge of the provided decal. Center the decal on

the side of the game and apply the decal, leaving a half inch around the outside that will

not be covered. Repeat the same step for the other side of the game.

Installing the Side Decals on a Countertop game

PM0350-02 MEGATOUCH™ TITANIUM 2 EDITION KIT 18

Problem:

The game locks up with “Operating System Not Found” or
“Disk Boot Failure”.

Solution:

Make sure you have installed the motherboard configura-
tion CD.
Check the ribbon cable connection and power connection
between the hard drive and the motherboard.

Problem:

The game locks up with “Invalid Drive Specification.”

Solution:

Remove the shunt from JP1.

Problem:

The game locks up with “Invalid Key”.

Solution:

Use the contact cleaner included with the kit on the pins
of the adapter board.
Raise the contact in the base of the key holder on the
adapter board, to ensure a good connection to the bottom
of the security key.

Problem:

The game locks up with “No Sound Driver Loaded”.

Solution:

Check the SIMMs, the Titanium program requires 32
MEG of memory.

Problem:

The game locks up at the XL Titanium screen, then
resets.

Solution:

Check the SIMMs, the Titanium program requires 32
MEG of memory.

Troubleshooting After Installation

19 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-02

Megatouch™ XL Titanim 2 Championship Edition
Instructions (For Championship Kits Only)

Overview

The Titanium 2 Championship Edition™ is a completely programmable tournament pro-

motion system, allowing players to compete for a prize pool based on the income from

premium-priced tournament games. The top three scorers, at the completion of a tourna-

ment, are entered into the Winners’ List for retention until they claim their prizes. The game

can be set to use cash prizes or redemption points depending on local laws.

Up to four tournaments can be programmed to run simultaneously. The settings for

each tournament, including game cost, rounds, starting time, ending time and date, duration

and prize pool, can be independently programmed to provide maximum flexibility and promo-

tional potential. Each tournament can be further programmed to be a single, repeating

tournament game or a sequence of different games, which change for each tournament

period.

Players who achieve one of the three high scores during a tournament must enter their

name, along with their own four-digit personal identification number (PIN). Should they finish

as one of the three highest scorers in that tournament, the PIN will be used to ensure positive

identification of the player. Provided an attendant is present, prizes may be claimed anytime

after the completion of a tournament. Once the prize is awarded, it is noted on the Winners’

List and is accounted for in the bookkeeping statistics.

PM0350-02 MEGATOUCH™ TITANIUM 2 EDITION KIT 20

Programming a Tournament

Press the SETUP button (located be-

hind the cashbox in countertop models

and on the PC shelf in upright models).

At the Setup Screen, touch the SYS-

TEM SETTINGS icon.

At the System Settings Screen, touch

the TOURNAMENT icon. This will take

you to the Tournament Controls screen

(see Figure 5). At this screen, touch

the SET-UP icon to enter the Tourna-

ment Clock/Currency Screen.

At the Clock/Currency Screen (see Fig-

ure 6) confirm the correct date and

time (if the date and/or time is incor-

rect, set the correct values using the

UP and DOWN arrows

next to each

field). Set the credit value by touching

the UP and DOWN arrows until the de-

sired value is shown. Set the appro-

priate currency type by touching the

desired currency symbol at the bottom

of the screen.

(NOTE: THE CREDIT VALUE IS
LOCKED AND CANNOT BE CHANGED
WHILE A TOURNAMENT IS RUNNING!)

Touch the “Next Page” icon to enter

the Tournament Setup Screen (see Fig-

ure 7).

FIGURE 5 - TOURNAMENT CONTROLS

SCREEN

B U T T O N

I C O N

D E S C R I P T I O N

S E T - U P

A c c e s s e s t h e T o u r n a m e n t
S e t - U p s c r e e n s .

C L E A R

W I N N E R S

E n t e r s   t h e   C le a r   W in n e r s
s c r e e n ,   w h ic h   a llo w s
y o u   t o   c le a r   a ll  w in n e r s   o r
c le a r   a ll  w in n e r s   w h o
h a v e   b e e n   a w a r d e d   p r iz e s .

R E S E T

A L L

E r a s e s   A L L   t o u r n a m e n t
in f o r m a t io n   f r o m
t h e   m e m o r y   o f   g a m e !
T h is   in c lu d e s   A L L   p r iz e
in f o r m a t io n !

FIGURE 6- CLOCK/CURRENCY SCREEN

21 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-02

FIGURE 7 - TOURNAMENT SETUP SCREEN

(EXPLANATION OF BUTTONS CONTINUES ON FOLLOWING PAGE)

Tournament

Sequence

A programmed sequence of up to 4 tournament
games. Touch a Tournament Sequence # to
program the desired tournament sequence (each
tournament sequence is programmed independently).

Tournament

Game

Sequence

To enter a game into the tournament game sequence,
touch the desired tournament game sequence field
and then touch the game name in the tournament
game list. Select the REPEAT icon to have the
programmed games repeat their sequence; select the
END icon to have the tournament games end after the
programmed sequence.

Tournament

Cost Fields

Touch an individual game to change the tournament
game cost. Use the up and down arrows to view all
available tournament games.

Tournament

Rounds Field

Touch the tournament round number to toggle the
number of rounds for the associated game. Game
rounds can be set from as low as 1 to as high as the
default number of rounds.

Reset Defaults

Touch to reset the default tournament settings.

PM0350-02 MEGATOUCH™ TITANIUM 2 EDITION KIT 22

Status

Light

This is the last step for programming a tournament
sequence.
Status can be toggled to RUNNING , DELAYED or

STOPPED by touching the associated traffic light

color.   RUNNING  (green) means the current
tournament will start upon returning to the Game Menu
Screen;  DELAYED  (yellow) means the current
tournament will start at the programmed time and date.
The tournament settings are  LOCKED  (red) for the
current tournament after credits have been played for
that tournament. WHEN THE STATUS IS  LOCKED,
ANY CHANGES TO THESE FIELDS WILL AFFECT
THE NEXT TOURNAMENT (S) ONLY.

Tournament

Duration

Sets duration for tournament games in the displayed
Tournament Sequence.

Prize Mode

Sets to POINTS or CASH, depending on tournament
type. When set to CASH, a message is displayed
reminding the user to confirm the legality of cash
tournaments in their area.

Prize

Pool

Sets the percentage of the tournament s total coin
drop to be used for tournament prizes.

Prize Pool

Starts At

Allows the operator to start the tournament with
cash/points already in the Prize Pool. The pool
increases as players deposit coins.

EXIT

Exits to the Tournament Controls screen. While in the
Tournament set up screen, highlighting any game in
the sequence, will turn this button to a cancel button
and will allow you to cancel out of the selected game
and restart your selection(s) for tournament play.

Operator

Set PIN

Displays the Set Attendant PIN keypad. The operator
can set up to four PINs to be used by attendants for
awarding prizes.

End Current

Game

Ends the current tournament game for the highlighted
sequence only.

Time and

Date

Fields

Touch the field you want to change and adjust the
value using the UP and DOWN arrows. Double-check
the time before performing Step 4. You cannot set the
time earlier than the current time. Tournament play
can be set in ten-minute increments past the real
time .

23 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-02

FIGURE 8 – WINNERS’ SCREEN

Awarding Prizes

Players qualify for prizes by finishing with one of the top three high scores for the

tournament.

To award a prize, access the Winners’ List (by touching the screen in the idle mode

and then selecting the CLAIM PRIZES icon, or by entering the tournament game

selection screen and selecting LAST WINNERS.) Touch the CHANGE GAME icon to

locate the Winners’ List for the desired tournament (use the UP and DOWN arrows

to page through the list of winners).

On the Winners’ List Screen, touch the players’ name to whom the prize will be

awarded.

When the PIN keypad is displayed, an attendant must enter one of the four, pre-

programmed attendant PINs (see Figure 8).

The player then enters their PIN to confirm the awarding of the prize.

The attendant must then touch the PRIZE AWARDED icon to register the payout.

(NOTE: TOUCHING “EXIT”, WITHOUT TOUCHING “PRIZE AWARDED,” WILL

CAUSE THE PRIZE AWARD SEQUENCE TO BE ABORTED. THE SEQUENCE

WILL HAVE TO BE REPEATED TO AWARD THE PRIZE).

Pay Without PIN

If a player should forget their PIN, the attendant can press the SETUP button in place

of entering the player’s PIN. The sequence will continue as though the PIN had been

entered. Touch PRIZE AWARDED to register the payout.

PM0350-02 MEGATOUCH™ TITANIUM 2 EDITION KIT 24

Merit Industries, Inc. Software License Agreement

Merit Industries, Inc. ("Licensor") is willing to license the enclosed software to you only if
you accept all of the terms in this license agreement.

Ownership of the Software

The enclosed Megatouch™ software program ("Software") and the accompanying
written materials are owned by Licensor and are protected by United States copyright
laws, by laws of other nations, and by international treaties.

Restrictions on Use and Transfer

If this Software package contains multiple media types (such as CD's, flash cards,
hard drives, etc), then you may use only the type of media appropriate for your
Machine. You may not use the other media types on another Machine, or transfer, or
assign them to another user except as part of the permanent transfer of the Software
and all written materials (as provided for below in paragraph 4).

You may make one copy of the software for backup purpose only. You may not copy
or make backup copies of any software security key or software security device
under any circumstances.

You may permanently transfer the right to use the Software and accompanying written
materials (including the most recent update and all prior versions) if you retain no
copies and the transferee agrees to be bound by the terms of this Agreement. Such a
transfer of this license to another party terminates your license. You may not other-
wise transfer or assign the right to use the Software, except as stated in this para-
graph.

You may not operate or allow the operation of the Software at locations where the
operation of such Software does not comply with all local, state, and other governmen-
tal body laws and regulations.

You may not modify, adapt, translate, reverse engineer, decompile, disassemble the
Software or create derivative works from the Software or any component thereof; nor
may you remove, modify or hide or otherwise make unreadable or non-viewable any
notice, legend, advice, watermark or other designation contained on the Software,
component thereof, or output therefrom.

You agree that the Software and the authorship, systems, ideas, methods of opera-
tion, documentation and other information contained therein, and all versions, modifica-
tions and adaptations thereto are proprietary intellectual properties of Licensor and are
protected by civil and criminal law, and by the law of copyright, trade secret, trademark
and patent of the United States and other countries.

Limited Warranty

Licensor warrants, solely for your benefit, that the Software will function in material
conformity, with its accompanying documentation for a period outlined in Licensor's
standard product warranty period after your receipt of the Software.

Licensor's Obligations Under Warranty

Licensor's sole obligation under the aforesaid warranty shall be to utilize commercially
reasonable efforts to correct or modify such portion of the Software as to make it
materially conform with the applicable documentation.

25 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-02

Grant Of License

10. Licensor grants to you the right to use one copy of the Software on a single Megatouch™

("Machine") accompanied by a single licensor factory authorized security key. Licen-
sor reserves the right to update versions of the software and the content to the
Machine as deemed appropriate by the Licensor.

Disclaimers

11.

EXCEPT AS PROVIDED IN THE SECTION ENTITLED "LIMITED WARRANTY", LICENSOR
MAKES NO OTHER PROMISES, REPRESENTATIONS OR WARRANTIES, WHETHER EX-
PRESSED OR IMPLIED, REGARDING OR RELATING TO THE SOFTWARE OR CONTENT
THEREIN OR TO ANY OTHER MATERIAL FURNISHED OR PROVIDED TO YOU PURSU-
ANT TO THIS AGREEMENT OR OTHERWISE AND LICENSOR SPECIFICALLY DISCLAIMS
ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE WITH RESPECT TO SAID MATERIALS OR THE USE THEREOF. TO THE MAXI-
MUM EXTENT ALLOWABLE BY LAW THE UNIFORM COMMERCIAL CODE OR OTHER
UNIFORM LAWS SHALL NOT APPLY TO THIS AGREEMENT.

Limitation on Liability

12. IN NO EVENT SHALL LICENSOR BE LIABLE UNDER ANY CLAIM, DEMAND OR ACTION

ARISING OUT OF OR RELATING TO THE SOFTWARE, OR LICENSOR'S PERFORMANCE
OR LACK THEREOF UNDER THIS AGREEMENT FOR ANY SPECIAL, INDIRECT, INCIDEN-
TAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, WHETHER OR NOT LICENSOR
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH CLAIM, DEMAND OR ACTION. IN
ADDITION, WITHOUT LIMITING THE FOREGOING, IN ALL EVENTS THE REMEDIES AVAIL-
ABLE TO YOU SHALL BE LIMITED TO THE AMOUNT PAID BY YOU TO LICENSOR FOR
THE SOFTWARE.

13. IN NO EVENT WILL LICENSOR BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY

LOSS OF PROFITS, LOST SAVINGS, OR OTHER INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF YOUR USE OR INABILITY TO USE THE SOFTWARE.

General

14. The validity and construction of this Agreement and of the rights and obligations herein

shall be determined and governed by the laws of the Commonwealth of Pennsylvania,
USA. Any controversy or claim arising out of or relating to this agreement shall be
resolved in the appropriate venue in Pennsylvania, USA.

15. Merit, in its sole discretion, may assign this agreement or any of its rights and obliga-

tions hereunder.

16. If you have any questions concerning this Agreement or wish to contact Licensor for

any reason, please write: Merit Industries, Inc., 2525 State Road, Bensalem, PA 19020,
USA.

PM0350-02 MEGATOUCH™ TITANIUM 2 EDITION KIT 26

Contrat de licence de logiciel de Merit Industries, Inc.

Merit Industries, Inc. (ci-après le "Concédant") est disposé à vous accorder la licence
d'utilisation du logiciel ci-inclus, à condition que vous vous engagiez à respecter tous les
termes, clauses et conditions du présent contrat de licence.

Droit de Propriété

Le logiciel Megatouch™ (ci-après le "logiciel") et toute la documentation écrite, restent
la propriété du Concédant et sont protégés par les lois du copywright des Etats-Unis,
ainsi que par les lois des autres pays et les traités internationaux.

Restriction d'Utilisation et Transfert

Si le présent logiciel comprend plusieurs types de composants (tels que CD-ROM,
cartes flash, disques durs, etc), vous ne pouvez utilisez que ceux qui conviennent à
votre appareil. Il est strictement interdit de les utiliser sur un autre appareil, les transférer
-ou les céder à un autre utilisateur, sauf si en cas de transfert permanent du logiciel et
de toute la documentation écrite (comme indiqué ci-dessous au paragraphe 4).

Il est interdit de copier le logiciel, à l'exception d'une copie de sauvegarde. Il est aussi
interdit de reproduire -ou faire des copies de sauvegarde des programmes de clé de
sécurité ou autres fichiers de sécurité, quelles que soient les circonstances.

Vous pouvez céder en permanence à un tiers -le droit d'utiliser le LOGICIEL et toute la
documentation écrite l'accompagnant, (ainsi que la plus récente mise-à-jour et toutes
autres anciennes versions) seulement si vous n'en gardez pas de copies, et si le
cessionnaire s'engage à respecter les termes, clauses et conditions du présent Contrat.
Cette cession à un tiers met fin à votre licence. Autrement, vous n'avez pas la
permission de transférer ou d'accorder à un tiers le droit d'utiliser le présent logiciel,
excepté que tel que décrit dans le présent paragraphe.

Il est interdit d'utiliser le présent logiciel ou de permettre son utilisation dans des em-
placements où l'utilisation du présent logiciel n'est pas conforme aux lois et réglementations
locales, nationales ou réglementations d'autres organismes gouvernementaux.

Il est interdit de modifier, adapter, traduire, démonter, décompiler, désassembler le
logiciel ou créer du matériel dérivé du logiciel ou de tout composant de celui-ci; vous ne
pouvez pas enlever, modifier ou cacher ou rendre illisible ou non-visible toute instruc-
tion, légende, information ou filigrane ou autre désignation qui apparaît dans le logiciel,
composant dudit logiciel ou résultant dudit logiciel.

Vous convenez que le logiciel et les droits d'auteur, les systèmes, les idées, les
méthodes d'utilisation, la documentation et autre information incluse, ainsi que toutes
les versions, modifications et adaptations qui s'y rattachent sont les propriétés
intellectuelles du Concédant et sont protégées par le droit civil et pénal et par la loit sur
le copyright, le secret commercial, la marque déposée et le brevet aux Etats-Unis et
dans les autres pays du monde.

Limite de Garantie

Le Concédant garantit seulement à votre intention, que le logiciel permettra une utilisation
conforme, avec la documentation l'accompagnant, pendant la période de temps indiquée
dans la période de garantie du produit standard du Concédant, à compter de la date de
livraison du logiciel.

27 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-02

Responsabilité du Concédant aux termes de la Garantie

La seule obligation du Concédant aux termes de la garantie susmentionnée sera de
faire tous les efforts commercialement raisonnables pour corriger ou modifier la partie
du logiciel pour le rendre matériellement conforme aux spécifications de la documenta-
tion.

Concession de Licence

10. Le Concédant vous accorde le droit d'utiliser une seule copie sur un seul Megatouch™

(ci-après "Appareil") accompagné d'une seule clé de sécurité autorisée en usine et
fournie par le Concédant. Le Concédant réserve le droit de mise-à-jour des versions
du logiciel et du contenu de l'Appareil, quand il juge nécessaire de le faire.

Exclusion de toute autre garantie

11.

EXCEPTE COMME PREVU DANS LA SECTION INTITULEE "LIMITE DE GARANTIE", LE
CONCEDANT N'ASSURE AUCUNE AUTRE GARANTIE DE QUELQUE NATURE ET A
QUELQUE TITRE QUE CE SOIT, EXPLICITE OU IMPLICITE, EN RAPPORT AVEC LE LOGICIEL
ET LES COMPOSANTS QUI L'ACCOMPAGNENT OU, LE CAS ECHEANT, TOUT SUPPORT
OU MATERIEL FOURNI CONFORMEMENT AU PRESENT CONTRAT. EN PARTICULIER, LE
CONCEDANT NE PEUT DONNER AUCUNE GARANTIE, DE QUELQUE NATURE QUE CE
SOIT, POUR LA COMMERCIALISATION DE TOUS LES PRODUITS EN RAPPORT AVEC LE
LOGICIEL OU AVEC L'UTILISATION DE CELUI-CI. DANS LA MESURE OU CELA EST
PERMIS PAR LA LOI, LE CODE UNIFORME COMMERCIAL OU AUTRE LOI UNIFORME NE
S'APPLIQUE PAS AU PRESENT CONTRAT.

Limite de Responsabilité

12. LE CONCEDANT NE SERA EN AUCUN CAS RESPONSABLE DE TOUTE RECLAMATION,

DEMANDE OU ACTION RESULTANT DE OU EN RAPPORT AVEC LE LOGICIEL OU LA
PERFORMANCE OU MANQUE DE PERFORMANCE DU CONCEDANT EN VERTU DU
PRESENT CONTRAT POUR TOUS DOMMAGES D'UNE NATURE QUI N'EST PAS PRESUMEE
PAR LA LOI ET QUI DOIVENT ETRE EXPRESSEMENT PROUVES, DOMMAGE INDIRECTS,
DOMMAGES-INTERETS POUR PREJUDICE MORAL, QUE LE CONCEDANT AIT ETE AVISE
OU NON DE LA POSSIBILITE D'UNE TELLE RECLAMATION, DEMANDE OU ACTION. DE
PLUS, SANS LIMITER CE QUI PRECEDE, LES DEDOMMAGEMENTS A VOTRE DISPOSI-
TION SERONT LIMITES AU MONTANT QUE VOUS AUREZ PAYE AU CONCEDANT POUR
LE LOGICIEL.

13. LE CONCEDANT NE SERA EN AUCUN CAS RESPONSABLE DES DOMMAGES, Y

COMPRIS TOUTE PERTE DE PROFIT, PERTES D'ECONOMIE OU TOUS AUTRES
DOMMAGES INDIRECTS OU DOMMAGES-INTERETS ACCESSOIRES DECOULANT DE
L'UTILISATION OU DE L'IMPOSSIBILITE D'UTILISATION DU LOGICIEL.

Dispositions Générales

14. La validité et la construction du présent Contrat et les droits et obligations ci-inclus

seront déterminés et régis par les lois du Commonwealth de Pennsylvanie aux États-
Unis. Toutes litiges ou réclamations résultant ou relatives au présent Contrat feront
l'objet d'une procédure de conciliation dans un établissement compétent en Pennsylvanie,
aux Etats-Unis.

15. Merit Industries -réserve le droit de transférer le présent contrat à un tiers ainsi que ses

droits et obligations ci-après.

16. Pour toutes questions concernant le présent Contrat -ou si vous désirez contacter le

Concédant pour une raison quelconque, veuillez écrire à: Merit Industries, Inc., 2525
State Road, Bensalem, PA 19020, Etats-Unis.

PM0350-02 MEGATOUCH™ TITANIUM 2 EDITION KIT 28

Merit Industries, Inc. Softwarelizenzabkommen

Merit Industries, Inc. („Lizenzgeber") ist nur dann bereit Ihnen eine Lizenz für die beiliegende
Software zu erteilen, wenn Sie alle Bestimmungen dieses Lizenzabkommens akzeptieren.

Eigentumsvorbehalt der Software

Das beiliegende Megatouch™ Softwareprogramm („Software") und die schriftlichen
Unterlagen sind Eigentum des Lizenzgebers und sind durch die Gesetze der Vereinigten
Staaten und anderer Länder und durch internationale Verträge urheberrechtlich
geschützt.

Beschränkungen im Gebrauch und Transfer

Sollte diese Softwarelieferung mehrere Medien enthalten (z.B. CD, Karten, Festplatten
usw.), dürfen Sie nur die für Ihre Maschine angebrachte Medienart verwenden. Die
anderen Medienarten dürfen nicht auf anderen Maschinen verwendet werden oder an
Dritte übergeben werden, abgesehen von einem endgültigen Transfer der Software
und aller schriftlichen Unterlagen (wie im untenstehenden Paragraphen 4 beschrieben).

Sie dürfen nur eine Sicherungskopie der Software herstellen. Unter keinen Umständen
dürfen Sie einen Softwaresicherungsschlüssel oder Sicherungsmaßnahmen kopieren
oder davon Sicherungskopien herstellen.

Sie dürfen das Nutzungsrecht für die Software und die schriftlichen Unterlagen
(einschließlich der aktuellen Version und aller vorhergehenden Versionen) an Dritte
übertragen, wenn Sie keine Kopie behalten und wenn der Empfänger die Bestimmungen
dieses Abkommens akzeptiert. Bei einem solchen Transfer der Lizenz an Dritte erlischt
Ihre Lizenz. Abgesehen von den Bestimmungen dieses Paragraphen sind alle anderen
Transfers oder Übertragungen der Nutzungsrechte für diese Software unerlaubt.

Sie dürfen die Software nicht benutzen oder eine Nutzung gestatten, wenn eine
solche Nutzung der Software irgendwelche Gesetze und Verordnungen der
kommunalen oder staatlichen Behörden verletzen würde.

Es ist Ihnen nicht gestattet, die Software abzuändern, zu verändern, zu übersetzen,
rückumzuwandeln, zu dekompilieren oder zu zerlegen, oder aus der Software oder
eines Teils davon andere Werke abzuleiten. Sie dürfen auch aus der Software, einem
Bestandteil der Software oder aus den Datenausgaben der Software keine Hinweise,
Bemerkungen, Ratschläge, Wasserzeichen oder andere Markierungen entfernen,
verändern, verbergen oder auf andere Art unlesbar machen.

Sie akzeptieren, dass die Software und die Urheberschaft, die Systeme, die Ideen, die
Arbeitsweisen, die Dokumentation und alle anderen darin enthaltenen Informationen
und alle Versionen, Veränderungen, und Bearbeitungen davon das geistige Eigentum
des Lizenzgebers sind, und dass sie durch Straf- und Zivilgesetzgebung und durch die
Copyright-, Geschäftsgeheimnis-, Warenzeichen- und Patentgesetze der Vereinigten
Staaten und anderer Länder geschützt sind.

Beschränkte Garantie

Der Lizenzgeber garantiert zu Ihren Gunsten, dass die Software für die angegebene
normale Garantiezeit des Lizenzgebers nach Ihrer Annahme der Software in erheblicher
Übereinstimmung mit der beiliegenden Dokumentation laufen wird.

Verpflichtung des Lizenzgebers im Rahmen der Garantie

Die ausschließliche Pflicht des Lizenzgebers im Rahmen der vorstehenden Garantie
besteht darin, alle geschäftlich vertretbaren Schritte zu unternehmen, um Teile der
Software zu berichtigen oder abzuändern, bis sie mit der beiliegenden Dokumentation
erheblich übereinstimmen.

29 MEGATOUCH™ TITANIUM 2 EDITION KIT PM0350-02

Übertragung der Lizenz

10. Der Lizenzgeber gibt Ihnen das Anrecht, eine Kopie der Software auf einer einzelnen

Megatouch™ („Maschine") mit einem einzelnen werksmäßig gestatteten
Sicherungsschlüssel zu benutzen. Der Lizenzgeber behält sich das Recht vor, nach
eigenem Ermessen die Software und den Inhalt der Maschine zu verbessern.

Beschränkungen

11.

ABGESEHEN VON DEN BESTIMMUNGEN DES PARAGRAPHEN „BESCHRÄNKTE
GARANTIE" GIBT DER LIZENZGEBER KEINE SONSTIGEN VERSPRECHEN,
VERPFLICHTUNGEN ODER GARANTIEN, OB AUSDRÜCKLICH ODER STILLSCHWEIGEND,
FÜR DIE SOFTWARE ODER IHRE BESTANDTEILE ODER FÜR ALLE ANDEREN
MATERIALIEN, DIE IHNEN IM RAHMEN DIESES ABKOMMENS ZUR VERFÜGUNG
GESTELLT ODER ÜBERLASSEN WERDEN, UND DER LIZENZGEBER LEHNT
AUSDRÜCKLICH ALLE ANSPRÜCHE AUF MARKTFÄHIGKEIT UND EIGNUNG DER
BESAGTEN MATERIALIEN FÜR DEN GEWÖHNLICHEN GEBRAUCH AB. SOWEIT
GESETZESMÄSSIG ZUGELASSEN, SOLLEN DIE HANDELSRECHTLICHE
GESETZGEBUNG AUS DEM UNIFORM COMMERCIAL CODE ODER ANDERE GESETZE
AUF DIESES ABKOMMEN NICHT ANWENDBAR SEIN.

Haftungsbeschränkung

12. DER LIZENZGEBER HAT KEINERLEI HAFTUNG BEI EINEM ANSPRUCH, EINER FORDERUNG

ODER EINER KLAGE, DIE AUF NUTZUNG DER SOFTWARE, DER LEISTUNG DES
LIZENZGEBERS ODER DESSEN VERSAGEN IM RAHMEN DIESES ABKOMMENS FÜR
JEGLICHE FOLGE-, INDIREKTE, SONDER- ODER NEBENSCHÄDEN BERUHEN, SELBST
WENN DER LIZENZGEBER AUF DIE MÖGLICHKEIT EINES SOLCHEN ANSPRUCHES,
EINER FORDERUNG ODER EINER KLAGE HINGEWIESEN WURDE. WEITERHIN UND
OHNE BESCHRÄNKUNG DES LETZTEN SATZES, DÜRFEN IN ALLEN FÄLLEN DIE IHNEN
ZUR VERFÜGUNG STEHENDEN ABHILFEN DIE VON IHNEN FÜR DIE SOFTWARE AN DEN
LIZENZGEBER GEZAHLTE SUMME NICHT ÜBERSCHREITEN.

13. DER LIZENZGEBER HAT IN KEINEM FALL EINE HAFTUNG IHNEN GEGENÜBER FÜR

SCHÄDEN, EINSCHLIESSLICH ETWAIGER GEWINNVERLUSTE, NICHT REALISIERTER
EINSPARUNGEN ODER ANDERER NEBEN- ODER FOLGESCHÄDEN, DIE AUS IHRER
VERWENDUNG ODER GEBRAUCHSUNFÄHIGKEIT DER SOFTWARE ENTSTEHEN.

Allgemein

14. Die Rechtsgültigkeit und Provisionen dieses Abkommens und der darin enthaltenen

Rechte und Pflichten werden durch die Gesetze des Commonwealth of Pennsylva-
nia bestimmt. Alle Ansprüche, die aus diesem Abkommen entspringen oder dieses
Abkommen betreffen, werden am jeweiligen Verhandlungsort in Pennsylvania, USA,
verhandelt.

15. Merit kann nach eigenem Ermessen dieses Abkommen oder jedes der darin enthaltenen

Rechte und Pflichten an Dritte abtreten.

16. Bei Rückfragen über dieses Abkommen oder wenn Sie den Lizenzgeber aus einem

anderen Grund kontaktieren wollen, bitte schreiben an: Merit Industries, Inc., 2525
State Road, Bensalem, PA 19020, USA.

PM0350-02 MEGATOUCH™ TITANIUM 2 EDITION KIT 30

NOTES:

__________________________________________________________________

_______________________________________________________________

________________________________________________________________

___________________________________________________________________

_______________________________________________________________

________________________________________________________________

__________________________________________________________________

_________________________________________________________________

______________________________________________________________

________________________________________________________________

___________________________________________________________________

__________________________________________________________________

_________________________________________________________________

_____________________________________________________________________

___________________________________________________________________

__________________________________________________________________

___________________________________________________________________

__________________________________________________________________

________________________________________________________________

_________________________________________________________________

Please read the enclosed license agreement. Operation of this game
constitutes acceptance of the Merit Software License Agreement.

Veuillez lire le contrat de licence d’utilisation ci-inclus. Si vous utilisez ce
jeu, vous vous engagez à respecter les termes et conditions du contrat de
licence d’utilisation du logiciel de Merit.

Bitte beiliegendes Lizenzabkommen durchlesen. Das Merit Software
Lizenzabkommen tritt in Kraft, sobald dieses Spiel verwendet wird.

MEGATOUCH TITANIUM 2 EDITION KIT

PM0350-02

Converted from the original PDF for faster on-screen reading. Use Download PDF for the source document.