PM0370-04 Modem and Card Swipe Installation Manual

Installation manual covering modem and card swipe setup and internet/credit authorization accounts for Megatouch Force Radion, Vibe, and Combo Jukebox games.

merit industries, inc.

PM0370-04

Visit the Merit Industries, Inc. Web site

http://www.meritind.com

Table of Contents

DISCLAIMER: In order to support credit card transactions through applicable Merit prod-
ucts, operators will need to establish accounts directly with various service providers
including an Internet service provider and a credit card authorization service. For operators’
convenience, Merit has included set-up forms and other information from various service
providers in this information packet. All agreements and registrations shall be directly
between operators and the third party service providers. All questions pertaining to regis-
tration, forms or contracts should be asked to the applicable third party. MERIT INDUSTRIES,
INC. MAKES NO REPRESENTATION, WARRANTY OR OTHER ENDORSEMENT WITH RE-
SPECT TO THE SERVICES OF ANY THIRD PARTY SERVICE PROVIDER INVOLVED IN THE
CREDIT CARD TRANSACTION PROCESS. MERIT INDUSTRIES, INC. IS NOT RESPONSIBLE
FOR THE ACTS OR OMISSIONS OF ANY THIRD PARTY SERVICE PROVIDERS. Operators
shall direct any technical or operational issues pertaining to the credit card transactions to
the appropriate third party service provider.

NOTE: The Internet service provider and credit card authorization service are only servicing

customers in the United States. If a customer outside of the U.S. is interested in installing a

credit card reader in a game, they will have to set up their own ISP and credit card authori-

zation accounts.

Establishing Internet & Credit Authorization Accounts ........ p. 1-2

Modem and Card Swipe Installation ....................................... p. 3-16

Megatouch FORCE Radion Games ........................................... p. 3-7

Modem Installation.................................................................. p. 3

Card Swipe Installation ........................................................... p. 3-5

Vibe Games ................................................................................. p. 8-10

Modem Installation.................................................................. p. 8

Card Swipe Installation ........................................................... p. 8-9

Megatouch Combo Jukebox ...................................................... p. 11-13

Modem Installation.................................................................. p. 11

Card Swipe Installation ........................................................... p. 11-12

Megatouch FORCE Fusion.......................................................... p. 15-18

Modem Installation.................................................................. p. 15

Card Swipe Installation ........................................................... p. 15-16

Credit Card Swipe Installation Instructions
CONTENTS:

1 CREDIT CARD SWIPE INSTALLATION INSTRUCTIONS

PM0370-04

Once you have received the informa-

tion from both B-2000 and

Authorize.Net, press the SETUP button

inside the cabinet to enter the informa-

tion in the Credit Card Setup Screens.

Touch the “Credit Card” icon on the Main

Menu Screen.

Touch the “Credit Card Setup” icon on

the Credit Card Menu Screen.

Enter the ISP Phone Number from

B-2000 and touch the “NEXT” icon.

Then, enter the B-2000 Login and touch

“NEXT”. Finally enter the B-2000 Pass-

word and touch the “NEXT” icon.

Enter the Credit Card Login from

Authorize.net and touch the “NEXT”

icon. Then, enter the Password from

Authorize.net and touch “NEXT”. The

Establishing Internet and Credit Authorization Accounts

QTY

PART NUMBER

DESCRIPTION

EC0084-01

CARD SWIPE

GL0029-01

LABEL WITH CREDIT CARD STICKERS

MW0684 -01

COIN BOX LEVELING BRACKET (RADION)

MW0898 -02

CARD READER MOUNTING BRACKET (FUSION)

HW4201

6 - 32 x ¼ L PAN PHL SEMS SCREW (RADION)

MP0043-01

CARD READER SPACER (RADION)

HW0116-01

CARD READER SPACER GASKET (RADION)

HW0115-01

CREDIT CARD PCB BOARD COVER (RADION)

HW4052

4 - 40 x ¼ L PAN/PHL MACHINE SCREW (VIBE)

HW4052-03

4 - 40 x ½ L PAN/PHL MACHINE SCREW (JUKEBOX)

HW4052-04

4 - 40 x 1 L PAN/PHL MACHINE SCREW (RADION/FUSION)

SA0432-01

30” HARNESS (RADION & FUSION)

SA0432-02

72” HARNESS (COMBO JUKEBOX)

MP0021-07

BILL ACCEPTOR FACEPLATE (RADION)

PM6064-03

BILL ACCEPTOR LABEL (RADION)

HW8811

TIE WRAP

MODEM ASSEMBLY (ONLY FOR KITS INCLUDING A MODEM)

PA0034-XX

MODEM

MW0466 -01

MODEM BRACKET (RADION)

HW4206

6 - 32 x ¼ L PAN PHL MACHINE SCREW

HW4365

6 - 32 x ¾ L PAN/SLT MACHINE SCREW (VIBE)

EC0074-06

6' RJ-11 PHONE CABLE

CN4452-02

RJ-11 COUPLER, 4CNDCT

CN4452-03

RJ-11 SPLITTER, M/F, 4CNDCT

EC0074-03

50' RJ-11 PHONE CABLE

Fill out the B2000.NET “Agreement for

Internet Service” and fax it to B-2000

at 215-699-8797. If you have any ques-

tions about the form, call 215-699-2400.

B-2000 will call back within 48 hours

and give you the phone number, login

name and password for Internet ser-

vice. The login and password can be

used on all machines, but the phone

number may change based on the lo-

cation.

Go to the Authorize.Net Web site

( h t t p : / / w w w . e - o n l i n e d a t a . c o m /

meritindustries) and complete the on-

line application for your credit authori-

zation account. After completing the

application, you will receive a Login ID

and temporary password via E-mail.

Follow the instructions in the E-mail to

attain a permanent password.

PM0370-04 CREDIT CARD SWIPE INSTALLATION INSTRUCTIONS

game will return to the Credit Card Menu

Screen.

Touch the “Dial-In Setup” icon on the

Credit Card Menu Screen.

At this screen, touch “YES” or “NO”

after “Wait For Tone” depending on

whether or not you have to wait for a

dial tone before dialing. Select a dialing

method (either tone or pulse) and in the

“Include Area Code” section, select

“YES” or “NO” depending on whether

or not you have to use an area code to

dial local numbers. If you need to use a

dialing prefix (such as a number to

reach an outside line), use the keypad

to enter the number. Insert a comma

after the number if the phone system

needs time to connect to an outside

line or to wait for a dial tone. Each

comma forces a delay of one second

before dialing. Select the dialing speed

(it is recommended that this remain at

FAST unless there is a problem dialing

out), then select to have the modem

sound turned on or off. After all of

these settings have been entered,

touch the “X” icon and confirm you want

to exit out of the Setup Screens.

10. Continue with “Modem Installation” in-

structions for your game.

Radion Games: See page 3.

Vibe Games: See page 8.

Combo Jukeboxes: See page 11.

Fusion Games: See page 15.

tion on motherboard (see Figure 2).

Make sure the serial cable does not

interfere with the CPU fan. If neces-

sary, tie wrap the cable.

Locate the free 4-pin connector on the

power supply harness. Attach this

connector to the J5 location on the

modem. See Figure 2.

Connect one end of the 6’ phone cable

to the J2 location on the modem and the

other end to the phone coupler on the

inside of the power entry assembly.

(The phone coupler is the one on the

right if you are facing the back of the

game). See Figure 2. Coil any excess

cable and tie wrap the coil to keep it in

place.

Connect the 50’ phone cable to the

phone coupler connector on the out-

side of the game (the phone coupler is

on the right if you are facing the back

of the game).

Secure the cable to the U-bolt on the

back of the game. (This will prevent

unnecessary strain on the connector

if the game is turned or moved.)

10. Plug the other end of the phone cable

into a phone jack.

Card Swipe Installation

11. Unlock and open the right side door (coin

box door) and remove the coin box.

12. If your game has an oversized coin box

and no speaker along the edge of the

game inside the door, use the supplied

sems screw (6 - 32 x 1/4 ) to install the

supplied coin box leveling bracket in

the manner shown in Figure 3, with the

corner of the bracket against the inner

edge of the game. Use the existing

screw hole on the outer edge of the

grate to install the bracket.

Megatouch FORCE Radion
Games

CAUTION: Before performing any upgrade,

it is important to remove any static electric-

ity from your body. To remove static elec-

tricity from your body, ground yourself by

touching a grounded piece of metal on the

game before handling any boards, chips,

connectors, etc. Failure to ground yourself

before performing an upgrade may result in

damage to your system and may prevent

you from performing the upgrade.

Modem Installation

If your game already has a modem installed,

(i.e. you already have installed TournaMAXX)

skip to “Card Swipe Installation.”

Turn off the game and disconnect it

from its power source.

Orient the modem as shown in Figure 2

and connect it to the modem bracket

(MW0466-01) using the four supplied

Phillips-head machine screws.

Unlock and open the rear door of the

game and locate the hole on the side of

the chassis where the modem assem-

bly will be secured (see Figure 2). If

there is a plastic coin guard in this lo-

cation, remove the screw securing the

guard and remove the guard from the

game.

Place the tabs on the bottom of the

modem bracket into the two slots on

the power supply bracket. Line up the

thumbscrew on the modem assembly

with the hole in the chassis and tighten

the thumbscrew to secure the modem

assembly (see Figure 2).

Attach one end of the supplied modem

serial cable (found in the bag with the

modem) to the J1 location on the mo-

dem and other end to the com 2 loca-

3 CREDIT CARD SWIPE INSTALLATION INSTRUCTIONS

PM0370-04

13. Unscrew the 2 screws securing the

bill acceptor alignment bracket and re-

move the screws, washers, bracket

and standoffs. Then unhook the spring

from the alignment bracket, leaving it

attached to the game.

14. Unscrew the 2 screws securing the

bottom of the bill acceptor faceplate and

remove and discard the plate. Keep

the screws to secure the supplied face-

plate.

15. Peel the backing from the supplied

spacer gasket and adhere the gasket

to one side of the supplied spacer, lin-

ing up the screw holes in each. See

Figure 4.

16. Place the spacer over the circuit board

on the credit card swipe and against

the reverse side of the swipe itself,

with the gasket side of the spacer fac-

ing away from the swipe.

17. Install the credit card swipe (with the

circuit board face up) and spacer in

the large opening of the supplied face-

plate by lining up the 2 screw holes in

the card swipe, spacer, and faceplate

and securing the assembly with the 2

supplied screws (4 - 40 x 1 L). The

gasket on the spacer should be against

the faceplate.

18. Connect the 11-pin connector on the

supplied 30” harness (SA0432-01) to

the J1 location on the card swipe.

19. Using Figure 5 for reference, peel the

backing from the tab on the supplied

circuit board cover and install the cover

over the credit card swipe by placing

the two flaps between the circuit board

and the plastic frame of the card swipe.

Then adhere the tab to the reverse side

of the faceplate.

PM0370-04 CREDIT CARD SWIPE INSTALLATION INSTRUCTIONS

20. Peel the backing from the supplied “In-

sert Bill Here” sticker and adhere it

above the bill acceptor slot as shown

in Figure 6.

21. Adhere the credit card logos for the

credit cards the game will accept di-

rectly on the game as shown in Figure

22. Install the faceplate assembly into the

game and secure the bottom with the 2

screws removed in step 14.

23. Replace the bill acceptor alignment

bracket and standoffs between the

bracket and the game and secure it to

the game with the 2 screws and wash-

ers removed in step 13. Also recon-

nect the spring to the bracket.

24. Route the wires from the credit card

swipe through the 2 cable clamps found

on the bottom of the chassis. Unscrew

the 2 screws securing the coin optic

board and route the wires behind the

coin optic board and through the large

slot in the chassis below the audio

board. Resecure the coin optic board

with the 2 screws. See Figure 7.

25. Connect the other end of the supplied

SA0432-01 harness (the 5-pin connec-

tor) to the J9 location on the I/O board.

See Figure 2.

26. Carefully replace the coin box.

27. Plug in the game and turn on the power.

28. Test the credit card swipe by pressing

the setup button to enter the setup

menu.

29. At the Main Menu, touch the “Credit

Card” icon.

FIGURE 2 - FORCE RADION GAME

(REAR VIEW)

MODEM SERIAL
CABLE (J1)

DETAIL VIEW

PHONE
CABLE
(J2)

4-PIN CONNECTOR

FROM POWER SUPPLY
HARNESS (J5)

PHILLIPS-HEAD
SCREWS SECURING
MODEM TO BRACKET
(4 PLACES)

TABS ON

MODEM BRACKET

COM 2

LOCATION ON

MOTHERBOARD

PHONE

COUPLER

MODEM

BRACKET

(MW0466-01)

J9 LOCATION

ON I/O BOARD

5 CREDIT CARD SWIPE INSTALLATION INSTRUCTIONS

PM0370-04

30. From the Credit Card Screen, touch the

“Credit Card Test” icon and follow the

directions on the screen. You will be

asked to swipe a credit card for test

purposes only. Your card will not be

charged during this test.

31. Replace the right side door and close

and lock the back door.

PM0370-04 CREDIT CARD SWIPE INSTALLATION INSTRUCTIONS

CORNER OF
BRACKET AGAINST
INNER EDGE OF
GAME

EXISTING

SCREW HOLE

FIGURE 3 - FORCE RADION GAME

WITH COIN BOX LEVELING BRACKET INSTALLED

SPACER GASKET
(ADHESIVE SIDE)

SPACER

FIGURE 4 - ADHERING GASKET TO SPACER - FORCE RADION

TAB (ADHESIVE SIDE)

PLACED AGAINST REVERSE

SIDE OF FACEPLATE

FLAPS PLACED BETWEEN

CIRCUIT BOARD AND

FRAME OF CARD SWIPE

(2 PLACES)

FIGURE 5 - CIRCUIT BOARD COVER - FORCE RADION

ROUTING OF
CARD SWIPE
HARNESS FROM
UNDER COIN OPTIC
BOARD THROUGH
SLOT IN CHASSIS

COIN OPTIC
BOARD

SLOT IN
CHASSIS

INSTALLED

CARD SWIPE

FIGURE 7 - FORCE RADION GAME

(SIDE VIEW)

FIGURE 6 - FORCE RADION GAME

BILL ACCEPTOR AND CREDIT CARD STICKER PLACEMENT

7 CREDIT CARD SWIPE INSTALLATION INSTRUCTIONS

PM0370-04

Vibe Games

CAUTION: Before performing any upgrade,

it is important to remove any static electric-

ity from your body. To remove static elec-

tricity from your body, ground yourself by

touching a grounded piece of metal on the

game before handling any boards, chips,

connectors, etc. Failure to ground yourself

before performing an upgrade may result in

damage to your system and may prevent

you from performing the upgrade.

Modem Installation

If your game already has a modem installed,

(i.e. you already have installed TournaMAXX)

skip to “Card Swipe Installation.”

Turn off the game and disconnect it

from its power source.

Unlock the lock on the processor cover

and loosen the 3 screws on either side

of the cover. Slide the cover away

from the connector side of the proces-

sor and lift the cover off of the unit.

Locate the free 4-pin connector routed

up through the metalwork near the

power supply (the harness is labeled

“modem”). Connect the 4-pin connec-

tor to the J5 location on the modem.

See Figure 8.

Locate the 5-pin connector routed up

through the metalwork near the same

location as the 4-pin connector. Con-

nect the 5-pin connector to the J1 loca-

tion on the modem. See Figure 8.

NOTE: The cable found in the box with the
modem can be discarded. It has already
been installed in the processor units.

Orient the supplied modem as shown

in Figure 8, lining up the four holes on

the modem with the four standoffs.

Secure the modem to the tray using the

four supplied slotted machine screws.

Connect one end of the supplied 6’

phone cable to the J2 location on the

modem and the other end to the inside

of the phone connector as shown in

Figure 8. Route the cable through the

cable clamps along the hard drive. Coil

any excess cable and tie wrap the coil

to keep it in place.

Connect the 50’ phone cable to the

phone connector on the outside of the

processor. See Figure 8.

Secure the cable to the U-bolt on the

processor. (This will prevent unnec-

essary strain on the connector if the

game is turned or moved.)

Carefully replace the top cover on the

processor and slide it completely in

place. Secure the cover by tightening

the 3 screws on each side of the unit.

10. Plug the other end of the phone cable

into a phone jack.

Card Swipe Installation

11. Unlock the terminal and push down on

the lock release while carefully open-

ing the front of the terminal.

12. Unscrew the 3 screws along the edge

of the metal credit card blockout plate

and the center screw in the middle of

the blockout plate securing the front

plastic blockout. See Figure 9. Re-

move the metal plate and the plastic

blockout.

13. The plastic guide on the card swipe

must be removed for installation in the

Vibe. Carefully unscrew the 4 Phillips-

head screws securing the plastic guide

to the unit and discard the plastic guide.

14. Insert the card swipe through the in-

side of the terminal as shown in Figure

9 and secure it with the 3 supplied 4 -

40 x 1/4 L screws.

PM0370-04 CREDIT CARD SWIPE INSTALLATION INSTRUCTIONS

FIGURE 8 - VIBE PROCESSOR (WITH COVER REMOVED)

SLOTTED SCREWS
SECURING
MODEM
TO STANDOFFS
(4 PLACES)

PHONE CABLE
(J2)

MODEM SERIAL CABLE
(J1)

4-PIN CONNECTOR

FROM POWER SUPPLY
HARNESS
(J5)

DETAIL VIEW

PHONE CONNECTOR

15. Locate the free 11-pin connector near

the card swipe and connect the 11-pin

connector to the J1 location on the card

swipe.

16. Plug in the game and turn on the power.

17. Test the credit card swipe by pressing

the setup button (located within the ter-

minal) to enter the setup menu.

18. Close and lock the terminal.

19. At the Main Menu, touch the “Credit

Card” icon.

20. From the Credit Card Screen, touch the

“Credit Card Test” icon and follow the

directions on the screen. You will be

asked to swipe a credit card for test

purposes only. Your card will not be

charged during this test.

21. Peel the backing from the supplied black

rectangle foundation sticker and ad-

here it above and to the right of the

credit swipe as shown in Figure 10.

22. Adhere the credit card logos for the

credit cards the game will accept on

the black foundation sticker. See Fig-

ure 10.

9 CREDIT CARD SWIPE INSTALLATION INSTRUCTIONS

PM0370-04

FIGURE 10 - VIBE

CREDIT CARD STICKER PLACEMENT

FIGURE 9 - THE VIBE TERMINAL IN OPEN POSITION

DETAIL VIEW

OF CARD SWIPE

(AFTER INSTALLATION)

SCREWS

SECURING

CARD SWIPE

(3 PLACES)

DETAIL VIEW

OF BLOCKOUT PLATE

(BEFORE INSTALLATION)

SCREWS

SECURING

METAL

BLOCKOUT

PLATE

(3 PLACES)

CENTER

SCREW

SECURING

PLASTIC

BLOCKOUT

PM0370-04 CREDIT CARD SWIPE INSTALLATION INSTRUCTIONS

Megatouch Combo Jukebox

CAUTION: Before performing any upgrade,

it is important to remove any static electric-

ity from your body. To remove static elec-

tricity from your body, ground yourself by

touching a grounded piece of metal on the

game before handling any boards, chips,

connectors, etc. Failure to ground yourself

before performing an upgrade may result in

damage to your system and may prevent

you from performing the upgrade.

Modem Installation

If your game already has a modem installed,

(i.e. you already have installed TournaMAXX)

skip to “Card Swipe Installation.”

Turn off the game and disconnect it

from its power source.

Unlock and remove the rear door and

turn off the internal power switch (lo-

cated above the cooling fan on the left

side).

Disconnect all connections to the I/O

board. This will allow for I/O board and

hard drive removal.

Remove the screw securing the hard

drive assembly to the electronics tray

and remove the hard drive assembly

from the tray. See Figure 11.

Locate the four standoffs under the

hard drive, then orient the supplied

modem, lining up the four holes on the

modem with the four standoffs. Se-

cure the modem to the tray using the

four supplied Phillips-head machine

screws. See Figure 11.

Attach one end of the supplied modem

serial cable (found in the box with the

modem) to the J1 location on the mo-

dem and the other end to the com 2

location on motherboard (see Figure

11). Make sure that the serial cable

does not interfere with the CPU fan. If

necessary, tie wrap the cable.

Locate the free 4-pin connector on the

power supply harness. Attach this

connector to the J5 location on the

modem. See Figure 11.

Connect one end of the supplied 6’

phone cable to the J2 location on the

modem and connect the other end to

the supplied phone splitter.

Using Figure 12, locate the phone con-

nector on the upper rear side of the

game. Unplug the existing phone cable

from the inside of the connector and

plug it into the open hole in the supplied

phone splitter. Insert the splitter into

the phone connector on the game. Coil

any excess cable and tie wrap the coil

to keep it in place.

10. Re-secure the hard drive over the mo-

dem with the screw removed in step 4.

Reconnect all of the connectors you

removed from the I/O board.

Card Swipe Installation

11. Unlock and open the front door of the

game.

12. Remove the 2 nuts securing the metal

blockout plate in the front door of the

game and remove the plate.

13. Insert the credit card swipe (with the

circuit board facing right) into the slot

in the front of the game. Secure the

card swipe with the 2 supplied 4 - 40 x

1/2 L screws through the inside of the

door.

11 CREDIT CARD SWIPE INSTALLATION INSTRUCTIONS

PM0370-04

14. Connect the 11-pin connector on the

supplied 72” harness (SA0432-02) to

the to the J1 location on the card swipe.

15. Route the card swipe harness under

the coin/bill area on the front door and

along the hinge side of the game be-

tween the power strip and the wall.

Continue routing the harness behind the

electronics tray and connect the 5-pin

connector to the J9 location on the I/O

board (see Figure 13). Use the sup-

plied tie wraps to secure the harness

to one of the existing harnesses in or-

der to keep the wiring in place.

16. Plug in the game and turn on the inter-

nal and external power switches.

17. Test the credit card swipe by pressing

the setup button (located on the I/O

board) to enter the setup menu. See

Figure 13.

18. At the Main Menu, touch the “Credit

Card” icon.

19. From the Credit Card Screen, touch the

“Credit Card Test” icon and follow the

directions on the screen. You will be

asked to swipe a credit card for test

purposes only. Your card will not be

charged during this test.

20. Close and lock the front and rear doors.

21. Peel the backing from the supplied black

rectangle foundation sticker and ad-

here it to the right of the credit swipe

as shown in Figure 14.

22. Adhere the credit card logos for the

credit cards the game will accept on

the black foundation sticker. See Fig-

ure 14.

PM0370-04 CREDIT CARD SWIPE INSTALLATION INSTRUCTIONS

FIGURE 12 - UPPER REAR VIEW OF MEGATOUCH COMBO JUKEBOX

PHONE CONNECTOR LOCATION

PHONE

CONNECTOR

13 CREDIT CARD SWIPE INSTALLATION INSTRUCTIONS

PM0370-04

FIGURE 11 - MEGATOUCH COMBO JUKEBOX (ELECTRONICS ASSEMBLY)

SCREWS SECURING MODEM

TO METALWORK

(4 PLACES)

4-PIN CONNECTOR

FROM POWER SUPPLY

HARNESS (J5)

PHONE CABLE (J2)

DETAIL VIEW

COM 2 LOCATION
ON MOTHERBOARD

SCREW
SECURING
HARD DRIVE

MODEM SERIAL CABLE (J1)

J9 LOCATION
ON I/O BOARD

FIGURE 14 - MEGATOUCH COMBO JUKEBOX

CREDIT CARD STICKER PLACEMENT

PM0370-04 CREDIT CARD SWIPE INSTALLATION INSTRUCTIONS

FIGURE 13 - FRONT VIEW OF MEGATOUCH COMBO JUKEBOX - I/O BOARD LOCATION

SETUP

BUTTON

J9 LOCATION
ON I/O BOARD

15 CREDIT CARD SWIPE INSTALLATION INSTRUCTIONS

PM0370-04

FORCE Fusion Games

CAUTION: Before performing any upgrade,

it is important to remove any static electric-

ity from your body. To remove static elec-

tricity from your body, ground yourself by

touching a grounded piece of metal on the

game before handling any boards, chips,

connectors, etc. Failure to ground yourself

before performing an upgrade may result in

damage to your system and may prevent

you from performing the upgrade.

Modem Installation

If your game already has a modem installed,

(i.e. you already have installed TournaMAXX)

skip to “Card Swipe Installation.”

Using a Phillips-head screwdriver, re-

move the two screws securing the

supplied modem and transceiver board

(see Figure 15). Disconnect the 2-pin

connector from J2 on the modem and

gently pull the modem from the trans-

ceiver board. The transceiver board

will not be used, but keep the screws

to secure the modem to the I/O board.

Turn off the game and disconnect it

from its power source.

Unlock and open the front bezel of the

game.

If your game has an electronics box,

remove the 2 screws securing the

cover and carefully remove the cover.

Also gently remove the wire guard

covering the inside of the power en-

try (located to the left of the cash box)

by pulling it straight forward and out

of the guides in the game. Then, re-

move the second wire guard located

to the right of the electronics box.

Locate the free end of the cable (la-

beled EC0098-XX) connected to the

inside of the phone connector in the

game (the phone connector is the con-

nector on the bottom). The free end of

the cable should be routed near the I/O

board. Connect the free 2-pin connec-

tor on the harness to the J2 location on

the modem. See Figure 16.

Line up the connector at J1 on the mo-

dem with the mating pins at J10 on the

I/O board and the two holes on the mo-

dem with the two standoffs on the I/O

board. Carefully press down on the

modem so that the connector is securely

mated. Fasten the modem to the I/O

board using the two screws removed

in step 1. See Figure 16.

Connect the supplied 50’ phone cable

to the phone coupler on the outside of

the game.

Plug the other end of the phone cable

into a phone jack.

Card Swipe Installation

Remove the metal blockout plate located

in the top left side of the front bezel.

Fusion games with electronics box:

The bezel must be removed in order to

access the blockout plate. Unscrew

the 6 thumbnuts (3 on each side of the

bezel) and gently remove the bezel from

the wood frame. Then remove the 4

nuts and bolts securing the blockout

plate and remove the plate from the

game. Install the supplied credit card

reader mounting plate (see Figure 17)

and secure the mounting plate with the

4 nuts and bolts.

Fusion games without electronics box:

Remove the 2 nuts securing the blockout

plate and remove the plate.

PM0370-04 CREDIT CARD SWIPE INSTALLATION INSTRUCTIONS

10. Connect the 11-pin connector on the

supplied 30” harness (SA0432-01) to

the J1 location on the card swipe.

11. Insert the credit card swipe (with the

circuit board facing right) into the card

reader mounting plate (for games with

electronics boxes) or access hole in

the bezel (for games without electron-

ics boxes). Then secure the card

swipe to the mounting plate with the 2

supplied screws (4 - 40 x 1 L) through

the inside of the bezel. If your game

has an electronics box, route the har-

ness from the card swipe through the

hole in the wood frame and then reat-

tach the bezel to the frame using the 6

thumbnuts.

12. Route the harness from the card swipe

through the cable clamps located along

the left side of the game. If your game

has an electronics box, route the cable

through the access panel on the right

side.

13. Connect the other end of the supplied

SA0432-01 harness (the 5-pin connec-

tor) to the J9 location on the I/O board.

See Figure 16. If your game has an

electronics box, resecure the cover

using the two screws. Also replace

the wire guard over the inside of the

power entry by sliding it into the upper

and lower guides. Then replace the

second wire guard to the right of the

electronics box.

14. Plug in the game and turn on the power.

15. Test the credit card swipe by pressing

the setup button to enter the setup

menu.

16. At the Main Menu, touch the “Credit

Card” icon.

17. From the Credit Card Screen, touch the

“Credit Card Test” icon and follow the

directions on the screen. You will be

asked to swipe a credit card for test

purposes only. Your card will not be

charged during this test.

18. Peel the backing from the supplied black

rectangle foundation sticker and ad-

here it above and to the right of the

credit swipe as shown in Figure 18.

19. Adhere the credit card logos for the

credit cards the game will accept on

the black foundation sticker. See Fig-

ure 18.

20. Close and lock the front bezel.

17 CREDIT CARD SWIPE INSTALLATION INSTRUCTIONS

PM0370-04

FIGURE 16 - FORCE FUSION

ELECTRONICS ASSEMBLY

FIGURE 15 - MODEM ASSEMBLY - MODEM AND TRANSCEIVER BOARD

SCREWS

SECURING

MODEM TO

TRANSCEIVER

BOARD

MODEM

TRANSCEIVER

BOARD

J10 LOCATION

J1 LOCATION

SCREWS

SECURING

MODEM

STANDOFFS

FOR MODEM

J2 LOCATION

MOUNTING
HOLES

MODEM

J9 LOCATION

FIGURE 18 - FORCE FUSION

CREDIT CARD STICKER PLACEMENT

FIGURE 17 - FORCE FUSION

CREDIT CARD READER MOUNTING PLATE

PM0370-04 CREDIT CARD SWIPE INSTALLATION INSTRUCTIONS

NOTES:

__________________________________________________________________

_______________________________________________________________

________________________________________________________________

___________________________________________________________________

_______________________________________________________________

________________________________________________________________

__________________________________________________________________

_________________________________________________________________

______________________________________________________________

________________________________________________________________

___________________________________________________________________

__________________________________________________________________

_________________________________________________________________

_____________________________________________________________________

___________________________________________________________________

__________________________________________________________________

___________________________________________________________________

__________________________________________________________________

________________________________________________________________

_________________________________________________________________

CREDIT CARD SWIPE INSTALLATION INSTRUCTIONS

PM0370-04

Converted from the original PDF for faster on-screen reading. Use Download PDF for the source document.